Interfacing 16x2 LCD with 8051

Interfacing 16×2 LCD with 8051

       LCD display is an inevitable part in almost all embedded projects and this article is about interfacing 16×2 LCD with 8051 microcontroller. Many guys find it hard to interface LCD module with the 8051 but the fact is that if you learn it properly, its a very easy job and by knowing it you can easily design embedded projects like digital voltmeter / ammeter, digital clock, home automation displays, status indicator display, digital code locks, digital speedometer/ odometer, display for music players etc etc. Thoroughly going through this article will make you able to display any text (including the extended characters) on any part of the 16×2 display screen. In order to understand the interfacing first you have to know about the 16×2 LCD module.

16×2 LCD module.

16×2 LCD module is a very common type of LCD module that is used in 8051 based embedded projects. It consists of 16 rows and 2 columns of 5×7 or 5×8 LCD dot matrices. The module were are talking about here is type number JHD162A which is a very popular one . It is available in a 16 pin package with back light ,contrast adjustment function and each dot matrix has 5×8 dot resolution. The pin numbers, their name and corresponding functions are shown in the table below.

Pin No:     Name         Function

  1              VSS           This pin must be connected to the ground

  2              VCC          Positive supply voltage pin (5V DC)

  3              VEE           Contrast adjustment

  4              RS              Register selection

  5              R/W           Read or write

  6              E                Enable

  7              DB0           Data

  8              DB1           Data

  9              DB2           Data

  10            DB3           Data

  11            DB4           Data

  12            DB5           Data

  13            DB6           Data

  14            DB7           Data

  15            LED+         Back light LED+

  16            LED-          Back light LED-

       VEE pin is meant for adjusting the contrast of the LCD display and the contrast can be adjusted by varying the voltage at this pin. This is done by connecting one end of a POT to the Vcc (5V), other end to the Ground and connecting the centre terminal (wiper) of of the POT to the VEE pin. See the circuit diagram for better understanding.

      The JHD162A has two built in registers namely data register and command register. Data register is for placing the data to be displayed, and the command register is to place the commands. The 16×2 LCD module has a set of commands each meant for doing a particular job with the display. We will discuss in detail about the commands later. High logic at the RS pin will select the data register and Low logic at the RS pin will select the command register. If we make the RS pin high and the put a data in the 8 bit data line (DB0 to DB7) , the LCD module will recognise it as a data to be displayed . If we make RS pin low and put a data on the data line, the module will recognise it as a command.

      R/W pin is meant for selecting between read and write modes. High level at this pin enables read mode and low level at this pin enables write mode.

E pin is for enabling the module. A high to low transition at this pin will enable the module.

DB0 to DB7 are the data pins. The data to be displayed and the command instructions are placed on these pins.

LED+ is the anode of the back light LED and this pin must be connected to Vcc through a suitable series current limiting resistor. LED- is the cathode of the back light LED and this pin must be connected to ground.

16×2 LCD module commands.

16×2 LCD module has a set of preset command instructions. Each command will make the module to do a particular task. The commonly used commands and their function are given in the table below.

Command                   Function

0F                              LCD ON, Cursor ON, Cursor blinking ON

01                              Clear screen

2                                Return home

4                                Decrement cursor

06                              Increment cursor

E                                Display ON ,Cursor ON

80                              Force cursor to the beginning of 1st line

C0                             Force cursor to the beginning of 2nd line

38                              Use 2 lines and 5×7 matrix

83                              Cursor line 1 position 3

3C                              Activate second line

0C3                            Jump to second line, position 3

OC1                           Jump to second line, position 1

LCD initialisation.

     The steps that has to be done for initialising the LCD display is given below and these steps are common for almost all applications.

• Send 38H to the 8 bit data line for initialisation
• Send 0FH for making LCD ON, cursor ON and cursor blinking ON.
• Send 06H for incrementing cursor position.
• Send 01H for clearing the display and return the cursor.

Sending data to the LCD.

       The steps for sending data to the LCD module is given below. I have already said that the LCD module has pins namely RS, R/W and E. It is the logic state of these pins that make the module to determine whether a given data input is a command or data to be displayed.

• Make R/W low.
• Make RS=0 if data byte is a command and make RS=1 if the data byte is a data to be displayed.
• Place data byte on the data register.
• Pulse E from high to low.
• Repeat above steps for sending another data.

Circuit diagram

Interfacing 16x2 LCD module to 8051

        The circuit diagram given above shows how to interface a 16×2 LCD module with AT89S1 microcontroller. Capacitor C3, resistor R3 and push button switch S1 forms the reset circuitry. Ceramic capacitors C1,C2 and crystal X1 is related to the clock circuitry which produces the system clock frequency. P1.0 to P1.7 pins of the microcontroller is connected to the DB0 to DB7 pins of the module respectively and through this route the data goes to the LCD module. P3.3, P3.4 and P3.5 are connected to the E, R/W, RS pins of the microcontroller and through this route the control signals are transferred to the LCD module. Resistor R1 limits the current through the back light LED and so do the back light intensity. POT R2 is used for adjusting the contrast of the display.

Program

MOV A,#38H // Use 2 lines and 5x7 matrix
ACALL CMND
MOV A,#0FH // LCD ON, cursor ON, cursor blinking ON
ACALL CMND
MOV A,#01H //Clear screen
ACALL CMND
MOV A,#06H //Increment cursor
ACALL CMND
MOV A,#82H //Cursor line one , position 2
ACALL CMND
MOV A,#3CH //Activate second line
ACALL CMND
MOV A,#49D
ACALL DISP
MOV A,#54D
ACALL DISP
MOV A,#88D
ACALL DISP
MOV A,#50D
ACALL DISP
MOV A,#32D
ACALL DISP
MOV A,#76D
ACALL DISP
MOV A,#67D
ACALL DISP
MOV A,#68D
ACALL DISP
MOV A,#0C1H //Jump to second line, position 1
ACALL CMND
MOV A,#67D
ACALL DISP
MOV A,#73D
ACALL DISP
MOV A,#82D
ACALL DISP
MOV A,#67D
ACALL DISP
MOV A,#85D
ACALL DISP
MOV A,#73D
ACALL DISP
MOV A,#84D
ACALL DISP
MOV A,#83D
ACALL DISP
MOV A,#84D
ACALL DISP
MOV A,#79D
ACALL DISP
MOV A,#68D
ACALL DISP
MOV A,#65D
ACALL DISP
MOV A,#89D
ACALL DISP
HERE: SJMP HERE
CMND: MOV P1,A
CLR P3.5
CLR P3.4
SETB P3.3
CLR P3.3
ACALL DELY
RET;
DISP:MOV P1,A
SETB P3.5
CLR P3.4
SETB P3.3
CLR P3.3
ACALL DELY
RET;
DELY: CLR P3.3
CLR P3.5
SETB P3.4
MOV P1,#0FFh
SETB P3.3
MOV A,P1
JB ACC.7,DELY
CLR P3.3
CLR P3.4
RET;

END

Subroutine CMND sets the logic of the RS, R/W, E pins of the LCD module so that the module recognises the input data ( given to DB0 to DB7) as a command.

Subroutine DISP sets the logic of the RS, R/W, E pins of the module so that the module recognises the input data as a data to be displayed .

Tweet